LA3600 DATASHEET PDF

VideoLeave a Comment on LA3600 DATASHEET PDF

LA3600 DATASHEET PDF

LA datasheet, LA circuit, LA data sheet: SANYO – 5-Band Graphic Equalizer,alldatasheet, datasheet, Datasheet search site for Electronic. LA datasheet LA component LA integrated circuit LA schematic LA application note A LA LA36 LA3. Sanyo LA datasheet, 5-Band Graphic Equalizer (1-page), LA datasheet, LA pdf, LA datasheet pdf, LA pinouts.

Author: Zulkirisar Gardakora
Country: Sao Tome and Principe
Language: English (Spanish)
Genre: Photos
Published (Last): 4 November 2006
Pages: 485
PDF File Size: 1.57 Mb
ePub File Size: 5.67 Mb
ISBN: 761-2-77297-687-8
Downloads: 16271
Price: Free* [*Free Regsitration Required]
Uploader: Voran

Hi Eric Nice question. Could i add this to my homemade tube amp, and take out the LA? LA is a single integrated single Op-amp, 5 datashest graphic equalizer IC which is very suitable for applications like portable stereo, radio sets, home theater systems, car audio systems etc. Capacitor C13 is a decoupling capacitor and C14 is a power supply filter circuit. C12 is the output capacitor and resistor R6 limits the supply current. Laa3600 email address will not be published.

LA Datasheet –

C12 is the output capacitor and resistor R6 limits the supply current. Gain of each band can be adjusted by using the corresponding potentiometers R1 to R5.

Then the contour of the knobs represents the frequency response of the tone control unit. This will hold good only when following are carried out. How we connect stereo input to this circuit?

Gain of each band can be adjusted by using the corresponding potentiometers R1 to R5. I used 9V DC for powering the circuit.

  APOLLO XP95 SMOKE PDF

LA3600 Datasheet PDF

This will hold good only when following are carried out. Previous post Next post.

Hi Eric Nice question. You may also like: Could i add this to my homemade tube amp, and take out the LA?

LA Sanyo 5-band Graphic Equalizer ChipFind Datasheet Archive |

Assemble the circuit on a good quality PCB. Previous post Next post. Capacitors C2, C4, C6, C8, C10 and C15 are the input capacitors and increasing the value of these capacitors will increase the low frequency response. In the circuit capacitors C1, C3, C5, C7 and C9 are used to fix the resonance frequency of the corresponding bands. The power supply must be well regulated and noise free. Most of the IC manufacturers call their multi band tone controls as graphic equalisers.

Then the contour of the knobs represents the frequency response of the tone control unit.

Leave a Reply Cancel reply Your email address will not be published. I used 9V DC for powering the circuit.

Your email address will not be published. Leave a Reply Cancel reply Your email address will not be published. If you use slider potentiometers as controls and mount them vertically in a sequence from left to right as R1 to R5 and as you slide it down, should cut the frequency spectrum for pa3600 it is meant and sliding up should boost.

The LA datashet be operated from anything between 5 to 15V DC and is extremely stable to capacitive loads. Most of the IC manufacturers call their multi band tone controls as graphic equalisers. In the circuit capacitors C1, C3, C5, C7 and C9 are used to fix the resonance frequency of the corresponding bands.

  FRAKTUR BASIS CRANII PDF

Capacitor C13 is a decoupling capacitor and C14 is a power supply filter circuit. Capacitors C2, C4, C6, C8, C10 and C15 are the input capacitors and increasing the value of these capacitors will increase the low frequency response.

How we connect stereo input to this circuit? Assemble the circuit on a good quality PCB. Datxsheet is a single integrated single Op-amp, 5 band graphic equalizer IC which is very suitable for applications like portable stereo, radio sets, home theater systems, car audio systems etc.

You may lz3600 like: The LA can be operated from anything between 5 to 15V DC and is extremely stable to capacitive loads. The power supply must be well regulated and noise free. If you use slider potentiometers as controls and mount them vertically in a sequence from left to right as R1 to R5 and as you slide it down, should cut the frequency spectrum for which it is meant and sliding up should boost.