Intecont Tersus – Free download as PDF File .pdf), Text File .txt) or read for weighing tasks better than % Manual and/or automatic zero setting Full. The INTECONT Tersus weighing elec- tronics is specially tion module, INTECONT Tersus optimally fits into any Manual and/or automatic zero setting. processes, the INTECONT Tersus meas- uring, control, and supervisory module, INTECONT Tersus optimally fits into any Manual and automatic zero setting.
|Country:||Bosnia & Herzegovina|
|Published (Last):||6 January 2014|
|PDF File Size:||20.39 Mb|
|ePub File Size:||4.5 Mb|
|Price:||Free* [*Free Regsitration Required]|
However, it ttersus always expe-dient to measure the length manually and to enter the exact value as a parameter. The basic diagram of the ITE inputs and outputs Bvhgb Instruction Manual Intecont Documents. Service and MaintenanceService and MaintenanceService and MaintenanceService and Maintenance All warning and instruction signs on the scales must be observed.
Belt impact measurement is constant to take changes in regular operation into account.
The selected space of the first level has an orange background. An exter-nal three-point untecont controller is needed with position-regulated prefeeders. Return to the normal display, or abort a function.
A belt weigher only measures and nitecont cannot influence the feed rate. It is recorded with a suitable measuring amplifier. Batch Abort Batch Call up the function block The value is recorded before the belt influence compensation function and before the delay at the dispatch point.
Pulses per length P However, they will not be cleared.
Using weighing modules with leaf spring parallel guidance, lever ratio is always 1. Parameters Function Range P The function block is two-staged. Tare or zero 2. Ibtecont intecont plus pdf -?
Published on Oct View 2. The functions of buttons 4 – 7 depend on the application software and parameterization. The conveying process ends once the batch setpoint has been reached. The devices may be operated only in the provided mamual. This function is only available in batching mode. Check the output regulator settings current limiting, speed range – Calibration error: Potential uses The evaluation electronics are used for technical weighing tasks in continuous processes in order to measure and record bulk material flows continuously and to high levels of accuracy.
Actual Flow Rate analog 3 s P Automatic 2 kg 5 kg 20 kg 50 kg kg kg 0. Belt Drift Related threshold: The current value of the P Watch belt circuit sensor service value; if need be, remedy fault.
This corrects the regular measurement in normal operation. It is output through contact X Turn off of total measurement The feeder drive can be switched on and off with the keys in this field if the mode of operation and the para-meterization permit it.
The test plug is available as an accessory. The scale has to run in volumetric operation.
Call up the function block The previously selected function will be displayed if no event is pending. The set and actual feed rates are compared and the difference conducted to the controller. Most of the details can be found in the technical tersuss sheets. Damaged or defective electrical components must immediately be re-placed or, if possible, repaired by qualified personnel.
PasswordPasswordPasswordPassword Passwords safeguard the parameters against unauthorized alteration.
Manual Intecont Tersus
The batching process can be controlled via the belt conveyor drive or via the bin feeder. When it reaches the batch setpoint, the conveyor belt and material prefeeder are turned off and the feeding process is ended. This manual is available in different forms: Any connected control systems in particular must be in safe state.
Notice is given automatically. Interrupt entry, continue with previous setpoint Delete symbols intdcont keyed in Starting and interrupting Start the batch and the conveying process begins Interrupting a ihtecont The batch is continued with the next start command.
Manual Intecont Tersus
Suitable calibration weights are available as accessories. The Nominal Belt Load calculated from the rated values functions internally.
The value for the plant can be adapted through P The batch has to be ended mannual cancelled. Function block Calibration CW: Selecting the physical output for triggering an external pulse counter for the measured quantity Bear in mind the limitations on speed and life cycle when selecting a relay output and set the weight equivalent for an impulse in P Ensure that the components have been de-energized.
Memory A P Mains power failure Scales data, calibration data, counter readings and quantity pulses not yet issued remain saved for unli-mited time after a mains power failure, and the time for approx.
The weighing platform must then be checked for jammed material particles.